How To Read Degrees On A Plat Map : Mapping | www.bookcliffsurvey.com : Minutes and seconds are small subdivisions of degrees.. How to read a plat map Subdivision plats must be completed by a licensed surveyor and meet the survey plat recording requirements of 27 v.s.a. The directions shown are for 66 degrees, 165 degrees, and 330 degrees, all using a 360 degree circle for direction. Either can be used to fit a plat to the commonly used 1:24,000 scale usgs quadrangle map, also referred to as a 7 1/2 minute map. Changes box provides the history of the map page.
The plat may also require a declination angle, but the default of zero works to get started. Two inputs are required to create a plat: The physical features that are commonly included on plat maps extend to streets, alleyways, and parks. This reads north, 63 degrees east. surveyors can mark the compass degree system as precisely as they want. South 70 degrees 07 minutes 27 seconds.
A site plan package can include: It is drawn to scale and records the land's size, boundary locations, nearby streets. Find the latitude and longitude markers, and use a ruler and a pencil to draw a line from your point to the nearest east or west edge of the map. An example heading might be n63e. The second format is degrees, minutes and seconds: This is for all of my real estate partners out there who have ever had a question on how to fully read a plat map. You'll notice that the first six columns are copied directly from the deed, but where did the other two columns come from? The line south 64 degrees 21 minutes 46 seconds east 630.09 feet to pipe in the centerline of ditch, thence with centerline of said ditch as follows:
Land surveyors usually earn bachelor degrees in cartography, geography and surveying.
Included are how to understand scales, markings (from the plat legend), property lines and corners, and the legal demarcation of boundaries, easements, and the natural situation. For example, a segment may have the notation n 15° 30′ 45″ e on one side of the line and the notation 166.25′ on the other side of the line. The plat is a type of property map, and it will describe every characteristic of a piece of land, from its size to its boundaries, and any roads or real property on the land. It is drawn to scale and records the land's size, boundary locations, nearby streets. For an actual compass bearing, note that a compass points at the north magnetic pole, not the true north pole (earth axis). How to read a plat map plat maps made easy this is an example of a los angeles county assessor's parcel/plat map along with brief descriptions as to what each item refers to on the map. Read the compass degree system by starting with a specific point on the compass (north, east, south or west), and then reading the number of the degrees to the next point on the compass. Metes and bounds are used on plat maps to describe the land and the properties that are found on the land. The usually use a system of bearings based on deviation from north or deviation from south. Ddd° mm' ss.s 32° 18' 23.1 n 122° 36' 52.5 w this is the most common format used to mark maps. Reading a land survey map accurately is a skill that takes study and practice to master. You can do this from google maps or perhaps you have a plat map. Then, draw a vertical line from your point to the nearest north or south edge of the map.
This article describes the land plat survey system and how to read a land survey plat. Two inputs are required to create a plat: A property plat is used by land developers, especially when it comes to subdividing a tract of raw land. Minutes and seconds are small subdivisions of degrees. The first three numbers indicate degrees = 119 degrees.
So, we have 0 to 90 degrees in each quadrant where 0 starts either on north or south and ends on the 90's at either west or east. Reading a land survey map accurately is a skill that takes study and practice to master. Changes box provides the history of the map page. To calculate decimal degrees, divide the seconds by 360, the minutes by 60, and leave the degrees alone, then add all three numbers together for each point. The starting point for latitude lines is the equator, which is at 0 degrees latitude. It's also the most cumbersome to work with. 89 degrees se would be slightly south of the right hand line. Find the latitude and longitude markers, and use a ruler and a pencil to draw a line from your point to the nearest east or west edge of the map.
Refers to the assessor's file for document number, re:
But if read 89 degrees ne, that is almost exactly due east and slightly north of the right hand line. This article describes the land plat survey system and how to read a land survey plat. It is drawn to scale and records the land's size, boundary locations, nearby streets. Subdivision plats must be completed by a licensed surveyor and meet the survey plat recording requirements of 27 v.s.a. Read the compass degree system by starting with a specific point on the compass (north, east, south or west), and then reading the number of the degrees to the next point on the compass. The correction for that may be a few degrees and depends on your location. Two inputs are required to create a plat: The usually use a system of bearings based on deviation from north or deviation from south. Then, take the numbers you got for the latitude and longitude of your point and put them together. Refers to the assessor's file for document number, re: Using their online map application, you can get a pretty good idea of where the parcel is and possibly turn imagery on to get some landmarks to use in locating it. For an actual compass bearing, note that a compass points at the north magnetic pole, not the true north pole (earth axis). Land surveyors usually earn bachelor degrees in cartography, geography and surveying.
Subdivision plats must be completed by a licensed surveyor and meet the survey plat recording requirements of 27 v.s.a. Plat plotter quick start guide. An example heading might be n63e. For example, a segment may have the notation n 15° 30′ 45″ e on one side of the line and the notation 166.25′ on the other side of the line. The second format is degrees, minutes and seconds:
For example, a segment may have the notation n 15° 30′ 45″ e on one side of the line and the notation 166.25′ on the other side of the line. County assessor's plat maps at one time were actually filed in large books. Every lot and block survey is part of a larger plat map which has a permanent reference monument or control point. For an actual compass bearing, note that a compass points at the north magnetic pole, not the true north pole (earth axis). Minutes and seconds are small subdivisions of degrees. The plat may also require a declination angle, but the default of zero works to get started. Information relative to roads, lighting, landscaping, natural features, access, soil erosion control, and stormwater management. It uses bearings and distances to measure the circumference of the property described in the legal description and is based on physical features of its.
N42w, or 42 degrees west of north
Information relative to roads, lighting, landscaping, natural features, access, soil erosion control, and stormwater management. The first three numbers indicate degrees = 119 degrees. Read the principal meridians and base lines. It uses bearings and distances to measure the circumference of the property described in the legal description and is based on physical features of its. A property plat is used by land developers, especially when it comes to subdividing a tract of raw land. South 22 degrees 32 minutes 51 seconds. Reading a land survey map accurately is a skill that takes study and practice to master. Then, take the numbers you got for the latitude and longitude of your point and put them together. This is for all of my real estate partners out there who have ever had a question on how to fully read a plat map. South 70 degrees 07 minutes 27 seconds. That is a compass bearing and is the way surveyors show angular direction on survey plats. Minutes and seconds are small subdivisions of degrees. Metes and bounds are used on plat maps to describe the land and the properties that are found on the land.